What is the best way to recover a motorcycle's battery?
Like other parts of motorcycles, batteries after a period of use will be weak and damaged. Speaking of batteries, we have the following two basic types: dry battery and water battery
- Because the solvent is not pure: this means that the water (H2O) in the bottle is not pure, there will be many gray-white solid precipitates on the surface of the plate. This solid precipitate (usually up to 98%) is lead sulfate (PbSO4).
Excessive occurrence of PbSo4 on the surface of the polar plate prevents the electrochemical process, thereby seriously reducing the capacity, increasing the internal resistance of the battery. Therefore, a part of the material of the anode is disintegrated into a dark brown muddy deposit at the bottom of the flask and creates an internal leakage current.
This causes the battery to not be fully charged, the maximum power is reduced and it is likely to be unusable.
When batteries encounter these situations, users need to perform recovery, or replace batteries when necessary.
However, the cost of renewal is often very high and a burden for users. Recovering batteries is the perfect job to save costs for users.
- Capacity measuring machine.
- Battery charging machine (2.4V / 50A max) and battery charger (12V, 24V, 48V, 72V, 96V and 220V / 20A to 150A).
- Chemicals of Epsom Salt, Sulfuric acide, distilled water ...
- Devices such as cutting, assembling, lifting, pulling, auxiliary equipment for chemical preparation and storage.
# Note: Epsom salt is another name for magnesium sulphate inorganic salts, containing: magnesium, sulfur and oxygen (Chemical Formula MgSO4). The name Epsom comes from a bitter water stream in the town of Epsom, England, about 14 miles from London.
Learn more: Structure and operating principle of Acid Batteries
- Check the bottle to see how the electrolyte solution is. Also, see the electrolyte density of each vessel.
- Determine the voltage and internal resistance of batteries.
- Soak the device with Epsom Salt solution (soak for at least 4 hours).
- You wait to load the battery. This load is done according to the recovery process in 20-24 hours.
- During the loading process, you re-titrate and add the solution, measure the capacity.
- Continue to load recovery in 10 hours.
- End recovery process.
- During charging, the battery must be placed in a well-ventilated place and away from sources of ignition. Because the battery charging process will cause explosive gases, you need to pay special attention to this problem.
- When acidic solution gets into the skin, you need to immediately flush and wash the acidic area several times, then immediately go to the nearest medical facility for treatment.
- Keep batteries away from children.
- Electronic meter
Step 2: Use an electronic clock to check the power still in the battery so that the battery can be damaged and the energy is gone.
Step 3: Remove the cap and seal the holes containing acid water. Use a small cylinder to pump distilled water into the holes in the flask, check the electrical current contact with the meter.
Step 4: Wait for a few minutes for the solution to flow evenly into the bottle, discharge the electricity. The discharge is done by using a connected light bulb and connecting to the two poles of the tank to discharge the power.
- This helps to push all the chemical parts after the time of accumulation at the two poles discharges and reconciles into the bottle. In order to retry the power supply in the tank, we use an electronic clock that has two poles of the bottle.
- You carry out such discharge and discharge operation until measuring the voltage of about 0 volts is able to overcome the power source in the battery.
Step 5: If you perform the above actions but still not, you use a 14v transformer to load the polarity back into the tank, charging for a few hours will improve the power in the bottle.
In order to increase the life of the vehicle, while helping the battery to be used for a long time, users need to pay attention to follow the manufacturer's recommendations and regularly maintain, clean, wash car wash With a car wash machine, ... is essential.
You can download the manual on how to recover motorbike batteries and how to recover many other types of batteries here: How To Recondition A Lead Acid Battery
Or you can download it here: https://ezbatteryreconditioning.com/video/
Why should I recover the motorcycle battery?
- Do batteries use for a long time- Because the solvent is not pure: this means that the water (H2O) in the bottle is not pure, there will be many gray-white solid precipitates on the surface of the plate. This solid precipitate (usually up to 98%) is lead sulfate (PbSO4).
Excessive occurrence of PbSo4 on the surface of the polar plate prevents the electrochemical process, thereby seriously reducing the capacity, increasing the internal resistance of the battery. Therefore, a part of the material of the anode is disintegrated into a dark brown muddy deposit at the bottom of the flask and creates an internal leakage current.
This causes the battery to not be fully charged, the maximum power is reduced and it is likely to be unusable.
When batteries encounter these situations, users need to perform recovery, or replace batteries when necessary.
However, the cost of renewal is often very high and a burden for users. Recovering batteries is the perfect job to save costs for users.
Process of recovering lead acid battery (Liquid Acid form)
# Tools to prepare
- Low impedance voltmeter 100 Ohm / volt.- Capacity measuring machine.
- Battery charging machine (2.4V / 50A max) and battery charger (12V, 24V, 48V, 72V, 96V and 220V / 20A to 150A).
- Chemicals of Epsom Salt, Sulfuric acide, distilled water ...
- Devices such as cutting, assembling, lifting, pulling, auxiliary equipment for chemical preparation and storage.
# Note: Epsom salt is another name for magnesium sulphate inorganic salts, containing: magnesium, sulfur and oxygen (Chemical Formula MgSO4). The name Epsom comes from a bitter water stream in the town of Epsom, England, about 14 miles from London.
Learn more: Structure and operating principle of Acid Batteries
Process of battery charging
# Step 1: Check battery status. This helps the user to check the status of the tank if it is blistering. This process is done as follows:
- Check the status of the terminal, observe whether the joints are rusty or corroded.- Check the bottle to see how the electrolyte solution is. Also, see the electrolyte density of each vessel.
- Determine the voltage and internal resistance of batteries.
# Step 2: Conduct an assessment of the status of each bottle
Based on the assessment of the status of the batteries to select the recovery chemical in accordance with the condition of the bottle.# Step 3: Proceed to recover the jar
- Remove the acid solution in the battery to the extent possible. Use Medical needles to clean and discharge.- Soak the device with Epsom Salt solution (soak for at least 4 hours).
- You wait to load the battery. This load is done according to the recovery process in 20-24 hours.
- During the loading process, you re-titrate and add the solution, measure the capacity.
- Continue to load recovery in 10 hours.
- End recovery process.
# Note safety when using batteries
- Do not leave the pole (+) and pole (-) of the battery connected together.- During charging, the battery must be placed in a well-ventilated place and away from sources of ignition. Because the battery charging process will cause explosive gases, you need to pay special attention to this problem.
- When acidic solution gets into the skin, you need to immediately flush and wash the acidic area several times, then immediately go to the nearest medical facility for treatment.
- Keep batteries away from children.
Process of recovering dry batteries for motorbikes
# Tools to prepare:
- Specialized dismantling tools- Electronic meter
# The process is as follows:
Step 1: You proceed to remove the battery from the motorbike to carry out the repair work.Step 2: Use an electronic clock to check the power still in the battery so that the battery can be damaged and the energy is gone.
Step 3: Remove the cap and seal the holes containing acid water. Use a small cylinder to pump distilled water into the holes in the flask, check the electrical current contact with the meter.
Step 4: Wait for a few minutes for the solution to flow evenly into the bottle, discharge the electricity. The discharge is done by using a connected light bulb and connecting to the two poles of the tank to discharge the power.
- This helps to push all the chemical parts after the time of accumulation at the two poles discharges and reconciles into the bottle. In order to retry the power supply in the tank, we use an electronic clock that has two poles of the bottle.
- You carry out such discharge and discharge operation until measuring the voltage of about 0 volts is able to overcome the power source in the battery.
Step 5: If you perform the above actions but still not, you use a 14v transformer to load the polarity back into the tank, charging for a few hours will improve the power in the bottle.
In order to increase the life of the vehicle, while helping the battery to be used for a long time, users need to pay attention to follow the manufacturer's recommendations and regularly maintain, clean, wash car wash With a car wash machine, ... is essential.
You can download the manual on how to recover motorbike batteries and how to recover many other types of batteries here: How To Recondition A Lead Acid Battery
Or you can download it here: https://ezbatteryreconditioning.com/video/
What is the best way to recover a motorcycle's battery?
Reviewed by Re-programming Life
on
2:56 AM
Rating:
Reviewed by Re-programming Life
on
2:56 AM
Rating:
No comments: